How does Chevy Invisible Trailer Work? – The Best Guide

You will get to know how to set up the Transparent Trailer View to fit an accessory camera on your trailer, measure specific dimensions and calibrate the system. You will also learn why it might not work correctly.

You will need to set it up before you get to know how does chevy invisible trailer works. Follow our steps to start.

How does Chevy Invisible Trailer Work?

Here is what this feature needs to be set up:

  • A truck that is properly equipped, including:
  • Package of technology
  • Auxiliary Camera Trailer (available as an Accessory)
  • A trailer that complies with the following requirements:
  • Type of conventional hitch
  • Trailer-style box or camping 
  • Length not exceeding 32 feet
  • Instructions and tools for installing the accessory camera are available 
  • A tape measure or a detailed list of the dimensions of your trailer

Before you purchase a vehicle or use it as a trailer, check the Owner’s Manual Trailer section carefully and how do chevy invisible trailer work. Passengers, freight, and accessories can reduce the amount that you can travel.

Step 1: Install the camera accessory

To use Transparent Trailer View, you must install your accessory trailer camera on the back of your trailer. Follow the instructions for camera installation when you purchased the camera that is summarized here for quick reference.

An accessory trailer camera must be mounted in a specific zone on your trailer’s rear to enable a transparent trailer view.

  • The perfect position for mounting the camera lens is:
  • Horizontal: centered on the trailer’s back
  • Vertically: 4 inches above the rear of your truck’s tailgate camera. Make sure you measure the pitch from floor to back of your camera (your trailer should be hitched when you do so), then add 4″ to the ideal vertical position on the back of your trailer. Important: Your goal for the camera installation should be no more than 8″ from that ideal position.
  • Angled down from horizontal 35 degrees. Markings on the installation unit can help you to find this position
  • Mount the camera. Mount the camera. Then route the cable harness and secure it outside the trailer. Read the camera installation instructions provided when buying for routing instructions.
  • Connect the camera to the trailer hitch connector. The rear trailer camera port should be connected.

Step 2: Enter the dimensions of the trailer in your trailer profile

Next, set up or select your Trailer Profile in the Trailering System (Trailering App)2 on the Home infotainment system screen using the Trailering icon. To set up the Transparent Trailer View, enter the detailed dimensions of your compatible trailer in your trailer profile.

  • Select Towing assistance setup for Transparent Trailer from your trailer profile screen.
  • Enter the seven necessary dimensions (up to the next inch or centimeter), using the diagrams to identify the correct measuring location. You are going to be asked to enter:
  1. Coupler center to the farthest back.
  2. Coupler center to the center of the tires
  3. The left edge of the trailer’s right edge
  4. Ground to the highest trailer point
  5. Ground to the top of the connector
  6. A couple of centers for the front wall of the trailer
  7. Hitch receiver to ball center
  • Select “Save and Continue” when all dimensions are entered
  • Start the detailed calibration steps in the next section

Enter your trailer’s dimensions on your compatible smartphone with myChevrolet or my GMC Mobile App3 if your connected services are active4. You don’t have to go between the trailer and the infotainment screen with measurements in this way. 

Step 3: Transparent Trailer View Calibrating

The last step is the process of calibration. This helps validate the dimensions you entered to give the trailer a clear and accurate view.

Although calibration starts automatically, you can monitor progress by tapping the CAMERA app icon on your Home screen infotainment system.

  • Tap the VIEW TRANSPARENT icon.
  • A progress bar is shown
  • To calibrate, go straight ahead until the progress bar is complete.
  • If you have to turn or speed up, the calibration will stop and restart after you are stretched out and slowed down.
  • The driving distance varies. It can take a few minutes
  • The calibration is carried out until it is complete
  • If you move to Park during the calibration process, the process must be restarted on the next step toward drive
  • Transparent Trailer View will be active when the calibration is complete. 

READ MORE: Are Social Security Benefits a Form of Socialism?

Andrew

Andrew is a professional writer with 7+ Years of experience. His style and uniqueness inspire and educate readers throughout the world.

You May Also Like

Leave a Reply

Your email address will not be published. Required fields are marked *